Tutors

Skill Bahn

PROGRAM OVERVIEW

CURRICULUM

  LESSON 1 - UNITS, FRACTIONS

  • General
  • Chapter 1: Unit
  • Chapter 2: Units for Length
  • Chapter 3: Units for Mass
  • Chapter 4: Units for Time
  • Chapter 5: Units for Capacity
  • Chapter 6: Units for Area
  • Chapter 7: Units for Volume
  • Chapter 9: Units for Speed
  • Chapter 10: Conversion for force and weight
  • Chapter 11: Units for Pressure
  • Chapter 12: Units for Density
  • Chapter 13: Units for Powers
  • Chapter 14: Units for Energy
  • Chapter 15: Units for Angle
  • Chapter 16: Temperature
  • Chapter 17: Conversion of smaller unit into higher unit
  • Chapter 18: BODMAS
  • Chapter 19: Fractions
  • Chapter 20: LCM and HCF
  • Chapter 21: Addition and subtraction of fractions
  • Chapter 22: Multiplication and division of fraction
  • Chapter 23: Simplification of fractions
  • Chapter 24: Decimal fraction
  • Chapter 25: Addition and subtraction of decimal fractions
  • Chapter 26: Multiplication and division of decimal fractions
  • Chapter 27: Simplification of decimals
  • Chapter 28: Fraction and decimal fraction

  LESSON 2 - SQUARE ROOT: RATIO AND PROPORTIONS, PERCENTAGE

  • Chapter 1: Square Root
  • Chapter 2: Factorization method
  • Chapter 3: Long division method
  • Chapter 4: Ratio
  • Chapter 5: Proportion
  • Chapter 6: Percentage

  LESSON 3 - MATERIAL SCIENCE

  • Chapter 6: Percentage
  • Chapter 2: Ferrous and Non-ferrous Metals
  • Chapter 3: Iron
  • Chapter 4: Steel
  • Chapter 5: Non ferrous metals and Non ferrous alloys

  LESSON 4 - MASS, WEIGHT, VOLUME AND DENSITY

  • Chapter 1: Mass, Weight and Density
  • Chapter 2: Density
  • Chapter 3: Solved Examples

  LESSON 5 - SPEED AND VELOCITY, WORK, POWER AND ENERGY

  • Chapter 1: Rest and Motion
  • Chapter 2: Velocity and acceleration
  • Chapter 3: Equation of motion
  • Chapter 4: Work
  • Chapter 5: Power
  • Chapter 6: Energy

  LESSON 6 - HEAT AND TEMPERATURE AND PRESSURE

  • Chapter 1: Introduction to heat
  • Chapter 2: Temperature
  • Chapter 3: Measuring heat energy
  • Chapter 4: Pyrometer
  • Chapter 5: Transmission of heat
  • Chapter 6: Pressure

  LESSON 7 - BASIC ELECTRICITY

  • Chapter 1: Introduction to basic principles of electricity
  • Chapter 2: Basic definitions
  • Chapter 3: Ohm’s law
  • Chapter 4: Circuit parameters
  • Chapter 5: Resistance series and parallel
  • Chapter 6: Conductor
  • Chapter 7: Insulator
  • Chapter 8: Work, Power and Energy

  LESSON 8 - MENSURATION

  • Chapter 1: Area and perimeter of square
  • Chapter 2: Area and perimeter of rectangle
  • Chapter 3: Area and perimeter of parallelogram
  • Chapter 4: Area and perimeter of triangle
  • Chapter 5: Area and perimeter of circle, semi circle
  • Chapter 6: Volume of solids – cube, cuboid
  • Chapter 7: Volume of solids cylinder
  • Chapter 8: Volume of solids Sphere
  • Chapter 9: Volume of solids Cone

  LESSON 9 - LEVERS AND SIMPLE MACHINES

  • Chapter 1: Levers and its types
  • Chapter 2: Simple Machines, Effort and Load, Mechanical Advantage
  • Chapter 3: Velocity Ratio, Efficiency of machine
  • Chapter 4: Problems on simple machines
  • Chapter 5: Problems on levers
  • Chapter 6: Screw jack

  LESSON 10 - TRIGONOMETRY

  • Chapter 1: Trigonometry
  • Chapter 2: Trigonometric ratios
  • Chapter 3: Trigonometry table
  • Chapter 4: Trigonometrical values for any angle